Tethys instrumens EXM500 online ammoniak (NH3) analyser
- extractief
- meetprincipe UV-spectroscopie
- intern gas circuit verwarmd 190°C
- geen meetgaskoeler nodig
- 19" rack model, 5U
- Mulitgas configuratie mogelijk: NH3, NO, NO2, SO2, H2S, CS2, C6H6, C8H10, NCl3
Behuizing 3HE 360mm diep, 2 aparte circuits 230V/16A met elk apart aan/uit schakelaar.
- 1x AX4 met Solid-state relais en 5-polige Binder plug achteraan (voor 30m leiding).
- 2x AX4 met 2x solid-state relais en 2x 7-polige binder plug achteraan (voor max. 10m leiding)
Aansluiting voor zowel korte als lange verwarmde leidingen (30 à 35m).
Zowel 5pins stekker als 7pins stekker aan te sluiten, echter slechts één leiding tegelijkertijd
Total vermogen 3650W, 230V/50Hz.
Hoofdschakelaar
PID temperatuurregeling
Operating voltage: 230V/50Hz
Switching power: max. 3650Watt ohmsche load
rule behavior: PID; regulator- accuracy 0,5%
sensor breach security: yes
sensor type: Pt100
Total outlet power no more than 16A ohmsche load.
network connection: power cable with Schuko power connector 1,5mm²
main switch illuminates: 2-pole
housing:plastic ABS and PC
Dimensions: 160x166x134mm (BxHxT)
Ambient temperature: 0 - 50°C
LED-display
EMV-compatibility: EN 61326
Interference Stability: industry request
Safety instructions: DIN EN 60204, EN 61010, BGV A3
Jumatherm is een merk van MARKUS DE VRIES.
Verwarmde sonde met vast aangesloten digitale regelaar (JUMO).
Geïntegreerd en verwarmd inox hulsje voor kleine filterhulzen of glaswol filter
Instelbare temperatuur 0 - 350°C
Materiaal: inox
Lengte 1m, 2m of ander lengtes op aanvraag
Op aanvraag met Harting-stekker of Binder-stekker voor externe temperatuur regelaar
Diameter 30mm
Ingang G1/2" binnendraad of G3/8" binnendraad in inschroefdop
Uitgang G1/2" binnendraad
Voeding 230V/50Hz met 1,5m netsnoer
Temperatuursensor Pt100
Verwarmingslint textielglas-geïsoleerd
Maximum temperatuur 350°C
Vermogen ca. 250W/m
Portable FID analyzer model OVF-3000 by J.U.M. Engineering
- Lightweight internal fuel storage, easy to operate
- Fully heated to 180°C
- Typical sensitivity 0.01 ppm CH4
- Internal sample pump and air pump
- Internal combustion air supply (No external air cylinder needed)
- Disposable sample filter in front panel
- Automatic flame out alarm contact and fuel shut off
- Sample pressure regulator not in contact with sample gas
- Multiple range capability; 5 selectable ranges are standard
Applications
- Stack gas emissions and all other Environmental and process applications
- Air and gas scrubber efficiency
- Process chemical gas analysis
- Personnel safety
- Solvent recovery
- Catalytic converter and thermal combustor testing
- Automotive and engine emissions
- Fence line (perimeter) monitoring
Complies analytically with EN 12619, EN 14181/ EN ISO 14956, (EU) and with EPA Method
25A and Method 503 (USA)
Method | Heated Flame Ionization Detector (HFID) |
Sensitivity | Max. 1 ppm CH4 full scale (100 ppb lowest detectable) |
Response time | @ sample inlet <0.2 seconds |
t90 time | @ sample inlet <1.2 seconds |
t90 time including 4X6mm sample line | Including heated sample line (7.5m) and sample probe filter: less than 8 seconds |
Zero drift | <2% full scale / 24h |
Span drift | <2% full scale / 24h |
Linearity | Up to 10.000 ppm full scale within 1.5% |
Oxygen synergism | < 2% FSD |
Measuring ranges (ppm) | Front panel turn switch: 0-10,100, 1.000, 10.000, 100.000, others on request. |
Signal outputs | 0-10 VDC, 4-20 mA, including RS-232 data output |
Display | 6- digit direct reading ppm units capability to measure up to three (3) overlapping measuring ranges without range change |
Total sample flow through | 2.5 to 2.8 l/min capacity @ operating temp. |
Sample filter | Disposable change filter in rear panel. Option OVE 32 |
Zero and Span gas | Front panel switch selectable and remote control, gas inlets on rear panel |
Zero and span adjust | Manual duo dial on front panel |
Fuel gas | 100% H2, consumption approx. 20 ml/min |
Burner air consumption | Built in burner air supply. No external cylinder air needed. consumption approximately 130 ml/min, all mixed fuel gases approx. 220 ml/min |
Oven temperature | 180°C (374°F) |
Temperature control | micro-processor PID controller |
Power requirements | 230VAC/50Hz, 850W (120 VAC/60Hz optional) |
Ambient temperature | 5-43°C (41-110°F) |
Dimensions | (W x D x H) 445 mm x 220 mm x 350 mm |
Weight | approx. 13 kg |
Bijlagen
Datalogging
To log the 0-10V and/or 4...20mA analog outputs.
PC-powered: Over USB Software-based J.U.M. MhcLog-109 (dual channel)
Hand held battery powered: Ahlborn ALMEMO 2590
Heated prefilter model VE112 by J.U.M. Engineering.
1 Heated sample inlet
2µm stainless steel sampler filter
5 'hot' outlets for gas cooler, FID, FTIR
Integrated heated sample pump 12l/min
Ideal for stationairy or transportable CEM's (Continuous Emission Monitoring system)
Jumatherm verwarmde leiding met interne PTFE leiding
Robuuste interne draagslang
Silicone eindkappen Isolatie met vilt en 7mm siliconeschuim
Buitenmantel in gevlochten polyamide of inox/RVS
Elektrisch verbruik 100W/m
Lengte op aanvraag (1 tot 35m of langer in speciale uitvoering)
Trekontlasting d.m.v. stalen trekkabel onder siliconeschuim isolatie ingewerkt
Opties:
Verwisselbare of vaste interne leiding
Tweede onverwarmde leiding bv. als kalibratieleiding
Ingewerkte stroom- of signaaldoorvoerkabel
Diameter interne PTFE leiding 6mm, 8mm of groter
Twee interne verwarmde leidingen i.p.v. één
Inox eindstukken voor het voorkomen van knikken van de PTFE leiding
Explosievrije versie (ATEX)
Interne leiding in PFA i.p.v. PTFE
Rugged transport case for mobile use.
Datalogging
To log the 0-10V and/or 4...20mA analog outputs.
PC-powered: Over USB Software-based J.U.M. MhcLog-109 (dual channel)
Hand held battery powered: Ahlborn ALMEMO 2590
Analyse-balgenpomp type MP-F 05
Materiaal: PTFE
Debiet: 320 l/h 5 Nl/min (320 Nl/h) bij een tegendruk op zuig- of perszijde van -/+ 50 mbar. Aansluiting: G1/4"i
Voeding: 230V/50Hz, IP55.
De balgenpompen MP-F zijn bijzonder geschikt voor het pompen van corrosieve gassen. Op vlak van constructie en prestaties zijn ze speciaal ontworpen voor de analysetechniek.
Pompdebiet : 5 Nl/min (320 Nl/h) bij een tegendruk op zuig- of perszijde van -/+ 50 mbar. Voeding 115V/60Hz of 230V/ 50Hz.
Heated FID analyser for TOC measurements.
TÜV approved for 2. BImSchV. 13. BImSchV and 17. BImSchV, fully complies with EN 12619, EN 13526 (EU) and EPA Method 25A and Method 503 (USA).
Features
- Maintenance free sample filter back purge system allows filter to be cleaned without dismantling (automatic optional)
- Built in burner air generator, no external air cylinder needed
- All components in contact with sample fully heated and controlled at 190 degree C
- Built-in sample pressure and sample pumps
- Automatic flame out alarm and contact
- Fast response within 1 second
- Low fuel consumption
- Very selective
- Microprocessor controlled PID-type temperature controller
- Remote control for sample, calibrate and back purge is standard
- Remote or automatic range change optional
Applications
- Stack gas hydrocarbon emissions monitoring
- Fence line monitoring
- Raw exhaust vehicle emissions analysis
- Catalytic converter testing
- Measuring engine combustion efficiency
- Hydrocarbon contamination monitoring in air and other gases
- Carbon adsorption regeneration control
- Detection of trace hydrocarbons in purity gases used in the semi conductor industry
- LEL monitor of solvent laden air
Bijlagen
Rugged transport case for mobile use. Front and back panel removable for easy access and operation.